-40%

104040 104040X Control Board for Reddy Heater Master Desa All-Pro and others

$ 31.09

Availability: 199 in stock
  • Brand: Desa
  • California Prop 65 Warning: WARNING: This product “may expose you to” a Proposition 65 chemical, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.”
  • MPN: 104040-**
  • Power Source: Electric
  • Condition: New
  • Model: 104068-02
  • Country/Region of Manufacture: United States
  • Product Type: Portable Heaters
  • Fuel Type: Kerosene and Diesel
  • All returns accepted: ReturnsNotAccepted

    Description

    This New Original Equipment Manufacturer Ignition Control Assembly part number 104040 was made for DESA International also known as All-Pro, Reddy Heater, Remington, Master Heater and Universal.
    The 104040 Ignition Control Assembly we are offering is the original equipment replacement part for the specific heaters listed and should be used according to the instructions.
    The 104040 Ignition Control fits the following Reddy Heater models:
    R35D, R35E, R40, R40T, R50BT, R55A, R55B, R55BT, R60, R60A, RM60, R70DT, R70ET, R70D, R110C, R110B, R110BT, R115, R115C, R115DT, R115T, RM115, RH125T, RH125AT, RHD125T, RL125T, RE125T, R155B, R155C, R155D, RM155, R165A, R165AT, R165CT, R165DT, RH170T, RH170AT, RHD170T, RE170T, RL170T, R200A, R200BT, RM200AT, RE200T, RHD200T…
    The 104040 Ignition Control fits the following Master Heater models:
    B70D, B70DT, B70ET, B110B, B100BT, B115, B115DT, M125T, M125AT, B150J, B150JT, B155T, B155CT, B155DT, B165A, B165CT, B165DT, M170T, M170AT, M200T, M200AT, B165AT, B200AT, B200BT…
    The 104040 Ignition Control fits the following Universal Heater models:
    UK55, UK70T, UK115T, UK165T…
    The 104040 Ignition Control fits the following All-Pro Heater models:
    PK55, PK60, PK70T, PK110, PK115T, PK165T…
    The 104040 Ignition Control fits the following Remington Heater models:
    REM35B, REM35C, REM40, REM50C, REM55A, REM55B, REM60, REM110B, REM110BT, REM115, REM115T, REM150E, REM155B, REM200AT…
    Warning:
    Never service a heater while it is plugged in, operating or still hot. Severe burns and electrical shock can occur.
    Note: Correct pump pressure must be calibrated after installation.
    This can be done using a low pressure gauge such as the DESA HA1180 gauge or an equivalent.
    This can also be done by turning your adjusting screw clockwise until the nose cone of the heater is glowing orange except for the last inch of you nose cone.
    This will give you the optimum heat from your unit as well as the least amount of fumes. If fumes burn your eyes discontinue use and consult a service technician.
    When removing replacement Rotor from the package and installing into the heater, do not strike or drop the rotor or damage may occur.
    Handle rotor by the body only.
    No warranty will be given for parts damaged during installation.
    If part is broken upon receipt a picture will need to be taken of the part in the unopened package before any parts exchange can occur.
    For any addition information please contact our office by email through our eBay store and one of our customer service agents will respond to your question in a timely manor.
    Our customer service department is available to answer parts compatibility questions by email Monday thru Friday from 10am to 4pm Central standard time.
    We do not offer technical service for repair of any type of equipment and have limited access to replacement parts.
    The most common replacement parts will be listed in our store and if what you are looking for is not listed in our store we will not be able to provide any additional non listed parts.