104068-02 Ignition Control Board 104068-03 104040 Reddy Remington Master Heaters

Description

This New Original Equipment Manufacturer Ignition Control Assembly part number 104068-02 is was made for DESA International also known as All-Pro, Reddy Heater, Remington, Master Heater and Universal.
The 104068-02 Ignition Control Assembly we are offering is the original equipment replacement part for the specific heaters listed and should be used according to the instructions.
This kit contains the following items in the 104068-02 Ignition Control Assembly
1 of part number 104040-01 Ignition Control Assembly Board with fuse.
The specific listed Ignition Control should always be used as the replacement part.
This new 106068-02 will replace the all of the following part numbers:
104040, 104040X,
104040-01, 104040W, 10235001, 102350-01, 104068-01, 104068-03, 10406803, 104040-02, 10404002, 10406801
Please Verify this is the part you need.
The 104068-03 Ignition Control fits the following Reddy Heater models:
R35D, R35E, R40, R40T, R50BT, R55A, R55B, R55BT, R60, R60A, RM60, R70DT, R70ET, R70D, R110C, R110B, R110BT, R115, R115C, R115DT, R115T, RM115, RH125T, RH125AT, RHD125T, RL125T, RE125T, R155B, R155C, R155D, RM155, R165A, R165AT, R165CT, R165DT, RH170T, RH170AT, RHD170T, RE170T, RL170T, R200A, R200BT, RM200AT, RE200T, RHD200T…
The 104068-03 Ignition Control fits the following Master Heater models:
B70D, B70DT, B70ET, B110B, B100BT, B115, B115DT, M125T, M125AT, B150J, B150JT, B155T, B155CT, B155DT, B165A, B165CT, B165DT, M170T, M170AT, M200T, M200AT, B165AT, B200AT, B200BT…
The 104068-03 Ignition Control fits the following Universal Heater models:
UK55, UK70T, UK115T, UK165T…
The 104068-02 Ignition Control fits the following All-Pro Heater models:
PK55, PK60, PK70T, PK110, PK115T, PK165T…
The 104068-02 Ignition Control fits the following Remington Heater models:
REM35B, REM35C, REM40, REM50C, REM55A, REM55B, REM60, REM110B, REM110BT, REM115, REM115T, REM150E, REM155B, REM200AT…
No returned will be accepted on this parts after the package has been installed
Warning:
Never service a heater while it is plugged in, operating or still hot. Severe burns and electrical shock can occur.
Note: Correct pump pressure must be calibrated after installation.
·
This can be done using a low pressure gauge such as the DESA HA1180 gauge or an equivalent.
·
This can also be done by turning your adjusting screw clockwise until the nose cone of the heater is glowing orange except for the last inch of you nose cone.
·
This will give you the optimum heat from your unit as well as the least amount of fumes. If fumes burn your eyes discontinue use and consult a service technician.
When removing replacement Rotor from the package and installing into the heater, do not strike or drop the rotor or damage may occur.
·
Handle rotor by the body only.
·
No warranty will be given for parts damaged during installation.
·
If part is broken upon receipt a picture will need to be taken of the part in the unopened package before any parts exchange can occur.